FRP installation in Azusa

What we build

• FRP installation

  Fiber-reinforced polymer systems installed on concrete and masonry to add strength where the structure needs it.

  What it involves: FRP installation

  Installed right, it adds strength to a beam, column, slab or wall with very little added thickness or weight.

  The work lives or dies on preparation. The surface is ground clean, cracks and spalls are repaired, corners are rounded, and the system is applied in the order and thickness the design calls for. We help you pick the right system for the job before anything goes on the wall.

  • A look at the concrete and what it needs to carry
  • Help choosing the right FRP system for the job
  • Surface grinding, crack repair and corner prep
  • Epoxy and fiber applied to the design layout
  • Finish coating where the area stays exposed

  What is FRP installation?

  It is the bonding of fiber-reinforced polymer, usually carbon or glass fiber fabric set in epoxy, onto concrete or masonry to add strength. It is used on beams, columns, slabs and walls.

  Do you install FRP in Azusa and nearby towns?

  Yes. Call or send the form with a few details about the structure.

• Concrete strengthening with FRP

  Cracked, overloaded or under-reinforced concrete strengthened with composite wraps and strips instead of demolition.

  What it involves: Concrete strengthening with FRP

  Concrete gets asked to do more than it was built for: a new load, a cut opening, corrosion that ate into the rebar, or a change in use. FRP strengthening wraps or strips the member so it can carry more, often in far less time than replacing it.

  A good job starts with understanding why the concrete needs help. Damaged areas are repaired first, then the composite is placed where it does the work, whether that is a column wrap, strips under a slab or plates on a beam.

  • Review of the concrete and the reason it needs strengthening
  • Repair of spalled or cracked areas first
  • Column wraps, beam plates or slab strips as needed
  • Coordination with your engineer on the design
  • Clean, finished surface when the work is done

  Can FRP strengthen an existing concrete beam or column?

  Often, yes. FRP can add bending, shear or confinement strength to existing members. Whether it fits your structure depends on the condition of the concrete and the loads, which is what the design checks.

  Is FRP strengthening faster than replacing concrete?

  In many cases it is, because the member stays in place and there is no demolition or curing of new concrete. The real timeline depends on prep and access.

• Attic insulation

  Attic insulation added or replaced so your house holds its temperature through Southern California summers.

  What it involves: Attic insulation

  A thin or packed-down attic lets heat pour into the rooms below. Adding insulation is one of the simpler ways to make a house easier to cool.

  We check what is up there now, how deep it is and whether anything needs fixing first, like gaps around lights and pipes or damaged material. Then the new insulation goes in evenly to the depth agreed, with vents kept clear.

  • Check of existing insulation depth and condition
  • Air sealing around gaps, pipes and fixtures
  • Old or damaged material removed when needed
  • New insulation installed to an even depth
  • Attic vents and access kept clear

  Do you do attic insulation outside Azusa?

  Yes. Our recent attic insulation work was in Los Angeles, and we cover Azusa and the nearby towns listed on this page.

• Structural changes and wall removal

  Walls opened up and structure changed with the load carried properly from the roof down to the footing.

  What it involves: Structural changes and wall removal

  Taking out a wall that holds up the house means the load has to go somewhere else: a beam, posts and a footing that can take it. That path has to be worked out before the wall comes down.

  We confirm what the wall carries, line up the drawings and permit, shore the structure while we work, and close it back up so the change looks like it was always there.

  • Check of whether the wall is load-bearing
  • Beam, post and footing sized for the load
  • Temporary shoring during the work
  • Permit and inspection coordinated
  • Drywall and finish patched to match

  Can you tell if a wall is load-bearing?

  We look at what sits above it, the framing direction and what runs below. When the answer affects the design, an engineer confirms it before any work starts.

• Additions and expansions

  New rooms tied into your existing house from foundation through roof and finish.

  What it involves: Additions and expansions

  An addition is a small new building joined to an old one. The tricky parts are the joins: the foundation, the roof tie-in and matching the floors, walls and finishes so the seam does not show.

  We write the scope, sort out drawings and permits, and build in order so inspections land where they should and the site keeps moving.

  • Written scope with what is and is not included
  • Drawings and permit submittals
  • Foundation, framing and roof tie-in
  • Trades scheduled around inspections
  • Finish matched to the existing house

  Do I need plans for a home addition?

  Yes, an addition needs drawings and a permit. Depending on the structure, an engineer or architect may need to stamp them. We help you sort out what your project requires.

• Whole-home renovation

  Several rooms or a whole house renovated in an order that avoids doing work twice.

  What it involves: Whole-home renovation

  A big renovation goes wrong in the sequence more often than in the craft. Plumbing and wiring roughed in before walls close, inspections before insulation, long-lead materials ordered before the trade that installs them shows up.

  We plan that order up front and show you anything we find behind the walls before it gets covered, so changes are talked through and priced before they are built.

  • Walk-through and written scope
  • Schedule built around inspections and lead times
  • Demolition, rough-in, inspection and finish in order
  • Hidden problems shown to you before they are covered
  • Changes priced before they are built

  Can we live in the house during a renovation?

  For a room or two, usually. For a full gut, rarely. It depends on whether a kitchen, bathroom and water stay in service, and we go over that during planning.

• Permits, plans and inspections

  Drawings, permit applications and inspections handled so your project does not stall at the building department.

  What it involves: Permits, plans and inspections

  Permits slow more jobs than the building does. Knowing what the city will ask for, and when the inspector needs to see each stage, keeps the crew from standing around.

  We help line up drawings and engineering when the work calls for it, submit the application, and schedule the build around each inspection.

  • Review of what your project needs permitted
  • Drawings and engineering coordinated as needed
  • Permit application submitted
  • Inspections scheduled at each stage

  How long do permits take?

  It depends on the city and the work. Simple jobs can be quick; structural work usually goes through plan review that takes longer. We build that time into the schedule.

How a project runs

1. 1

   Talk

   You call or send the form with a few lines about the job. We ask what you are trying to fix or build and set a time to see it.

2. 2

   Scope

   We look at the site, take measurements and write down what the work includes, what it does not and what still needs to be decided.

3. 3

   Plan

   Drawings, engineering and permits where the work needs them, plus a schedule that allows for review and material lead times.

4. 4

   Build

   The work goes in order, with inspections where they belong. Anything unexpected is shown to you and talked through before it is covered.

5. 5

   Walk

   We walk the finished work with you and go through a list of anything left to fix before we call the job done.